Cleaning Machines

The Öko 1000mP and 2000mP are µP-controlled cleaning machines, which work on a water basis with special cleaners and hot-air drying, for PCB assemblies, misprints, small components, etc.

Features of the Öko 1000mP:

Capacity: 48 eurocards
Cleaning time: approx. 1 hour
Drying time: approx. 1 hour
Total cleaning cost per eurocard: approx. 0.03 EUR
Manual Time cycle for 48 eurocards: approx. 5 min.
Universal Microprocessor control
4 standard programs
Programming of individual memory-storable cleaning programs
Protocol output via a RS-232 interface

Technical Data for the Öko 1000mP:

Cleaning temperature: 20°C - 70°C
Cleaning time: 5 - 40Min.
Rinsing temperature: 20°C - 70°C
Rinse cycle time: 2 - 10 min.
Number of rinses: 0 - 5
Hot-air drying temperature: 50°C - 100°C
Hot-air drying time: 0 - 5 hours
Electrical connection: 230V AC
Power: 2.1 kw
Noise level: approx. 55dB (A)
Water consumption per filling: approx. 3 liters of DEIONIZED-water ¨
Internal basket dimensions: W390xD280xH500mm
Circuit board size (when using the basket): 390x260mm
Circuit board size (when using a frame): 340x260mm
External dimensions: H460xW560xD620mm
Weight: approx. 24 kg

Features of the Öko 2000mP:

Capacity: 170 eurocards
Cleaning time: approx. 1 hour
Drying time: approx. 1 hour
Total cleaning cost per eurocard: approx. 0.03 EUR
Manual Time cycle for 170 eurocards: approx. 5 min.
Universal microprocessor control
4 standard programs
Programming of individual memory-storable cleaning programs
Protocol output via a RS-232 interface

Technical Data for the Öko 2000mP:

Cleaning temperature: 20°C - 70°C
Cleaning time: 5 - 40 min.
Rinsing temperature: 20°C - 70°C
Rinse cycle time: 2 - 10 min.
Number of rinses: 0 - 6
Hot-air drying temperature: 50°C - 100°C
Hot-air drying time: 0 - 5 hours
Electrical connection: 230V AC
Power: 3.0 kw
Noise level: approx. 55dB (A)
Water consumption per filling: approx. 5 - 6 liters of DEIONIZED-water
Internal dimensions: W490xD470xH500mm
Circuit board size without upper level: 438x260mm (bottom)
438x200mm (top)
Solder frame size: 510xx660mm
External dimensions: H820xW600xD720mm
Weight: approx. 53 kg

The NE Ion exchanger, which operates on the mixed bed principle, delivers pure, deionized water in a matter of only seconds. The capacity of the high-performance exchanger resin is efficiently used as a result of optimal water distribution and control technology. In this way, in addition to their extraordinary capacity, these machines achieve the purest water quality of up to 0.055µS/cm. The purified water is pH-neutral and free of all dissolved salts as well as silica and carbonic acids.
As a result of the use of high-quality materials and quality-conscious processing, NE ion exchangers are among the most dependable and durable machines available today.
NE ion exchanger cartridges can be regenerated as often as desired without any loss of quality.

Technical Data for the NE Ion Exchanger:

Power: 800l/h
Capacity: 2800l (at 10°d H)
1400l (at 20°d H)
Operating pressure: up to 10bar
Dimensions: D240xH570mm

Blechstüble Daunquart Cleaning Equipment

WASCHBÄR template washer – a fully automatic three-compartment washer for templates, printed circuit boards with a defective print and soldering frames for the electronic industry.

Function principle:

In the washing compartment [1] the screen is washed by two rotating arms with nozzles dispersing 130 litres of the washing solution per minute.
When transported automatically to the drying compartment, the screen is in the rinsing compartment [2] rinsed either with clean water or with a cleaning liquid and then blown over with compressed air.
In the drying compartment [3] the screen is thanks to the machine’s ingenious drying technique dried within a very short time (metal templates in about 5 minutes per template, PumpPrint templates in about 10 minutes!).
Simple control panel [4].
Floor-standing tank with an integral latticed grate (pedestal) [5].

Waschbär template washer features:

Maximum template size 600 × 600 mm
Low energy consumption
Drying time about 10 minutes
Floor-standing tank with a latticed grate
Suitable for twin-water-based cleaning products washing products with flash point above 55°C
Power supply 400 V/50 Hz/16 A
Electric controls (programmable system)
Electric washing circuit pump
Thermostatically controlled 2 kW heating
10-inch washing circuit fine filter
20-inch rinsing circuit fine filter

For best results we recommend to use ZESTRO solvents!

Waschbiber template washer

WASCHBIBER is our semi-automatic template washer for the electronic industry with manual template manipulation.

Function principle:

In the washing compartment [1] the template is washed by two rotating arms with nozzles dispersing 130 litres of the washing solution per minute.
The template is rinsed by manually submerging it in the rinsing compartment tank [2].
In the drying compartment [3] the template is dried within a very short time (e.g. metal templates in about 5 minutes).
Removable tank [4] – it is very easy to clean.
Floor-standing tank with an integral latticed grate.

Waschbiber template washer features:

Maximum template size 740 × 740 mm
Low energy consumption due to the separate washing, rinsing and drying compartments
Concurrent template washing and drying
Power supply 400 V / 50 Hz /16 A
Electrical controls (programmable system)
Electric washing circuit pump
Thermostatically controlled 2 kW heating
10-inch fine filter

Tested and recommended with ZESTRON water-based VIGON SD200 and ATRON SP200 cleaning products.

For best washing results we recommend to use ZESTRON solvents!

Waschmaus template washer

Waschmaus The washing takes place in a washing compartment using two rotating arms with nozzles. The templates are rinsed manually by submerging them into a rinsing tank. The templates are dried in a heated drying compartment.

Waschmaus template washer features:

Maximum template size 600 × 600 mm
Separate compartments for washing, rinsing and drying
Pneumatic controls
Mobile washer on wheels with heating and fine filter
Suitable for twin-water-based washing products with flash point above 55°C
Power supply 230 V / 50 Hz / 16 A
Requires a connection to compressed air
Electric washing circuit pump
Thermostatically controlled 2 kW heating
10-inch fine filter

For best washing results we recommend to use ZESTRON solvents!

With Ultrasonic Cleaning Machines from Martin Walter, cleaning work can be carried out in the areas of plating, electronics, medical technology, maintenance and servicing. This high-quality system of generators and oscillators is ready with numerous option combinations for goods of various shapes with any type of contamination. We offer a series of small machines (bench top models) as well as a series of larger models (industrial line).

Features of the Powersonic Bench top Models:

Vat content: 0.8 - 26.0l
Frequency: 45 - 132 kHz
Analog and digital design
Drain spigot present in models with vat content above 8.8l

Features of the Industrial-Line:

Vat content: 40 - 360l
Frequency: 25kHz, 40kHz or 132kHz
Vat content: 0.8 - 26.0l
Frequency: 45 - 132 kHz
Analog and digital design
Drain spigot present in models with vat content above 8.8l